Ipod classic what kind of hard drive

Ideally, the angle should be as vertical as possible while still clearing the edge of the rear panel. Insert a plastic opening tool into the seam between the front and back of the iPod. Insert another plastic opening tool into the seam between the front and back of the iPod, leaving at least 1. There are thin metal rails running along the inside of the rear panel, so take great care when inserting the putty knife.

Once the putty knife has cleared the lip of the rear panel, pivot the putty knife so that it is vertical, and carefully but firmly wiggle it straight down into the gap between the opening tools.

Push with your fingers on the rear panel behind the putty knife to minimize bending. Slowly flex the putty knife, as shown in the picture, to ensure that most of the metal tabs on this side of the iPod are disengaged. The theory behind this method is, rather than attempting to not bend the rear panel at all, to bend it in a favorable manner that allows you to easily restore it later.

Therefore, any bend in the sides of the rear panel should be drawing the lip of the rear panel away from the iPod, rather than pushing out on the curved surface.

This method also disengages as many of the side clips as possible. Remove the putty knife from the iPod and reinsert it closer to the corner of the iPod, using the same wiggle method as before. Near the headphone jack, insert a plastic opening tool into the seam between the front and back of the iPod.

You may find it easier to carefully flex the putty knife downward in order to create more of a gap for the opening tool, but be sure not to bend the corner of the rear panel! Near the center of the display, carefully insert a metal spudger into the gap created by the plastic opening tool.

It is easy to create a noticeable bump in the rear panel here that is difficult to repair. When prying the tab free, try to have the metal spudger pivot on the edge of the rear panel rather than bending the rear panel outward. Near the other top corner, insert a plastic opening tool into the seam between the front and back of the iPod. On the other side, insert a plastic opening tool into the seam between the front and back of the iPod.

You may find it easier to angle the opening tool stuck in the top corner in order to create a sufficient gap. Remove the opening tool from the top corner and insert it into the seam between the front and back of the iPod, leaving at least 1.

Again, there are thin metal rails running along the inside of the rear panel, so take great care when inserting the putty knife. Once the putty knife has cleared the lip of the rear panel, angle the putty knife so that it is vertical, and carefully but firmly wiggle it straight down into the iPod via the gap between the plastic opening tools.

Ever so slightly flex the putty knife to ensure that most of the metal tabs on this side of the iPod are disengaged. The metal clips near the corners are notorious for tenaciously gripping the front panel. It is necessary to disengage these clips in order to open the iPod.

Gently wiggle the metal spudger down so that it is all the way in the rear panel. Continue to push up on the front panel with the metal spudger until the metal clip releases. There are two ribbon cables connecting the rear panel to the rest of the iPod. In the following step, be careful not to damage these ribbon cables. Gently GENTLY disengage the remaining clips on the rear panel by pulling the tops of the front and rear panels away from each other think of the bottom of the iPod as a hinge , taking great care not to damage the ribbon cables holding the two halves together.

Use a spudger to slide up the connector holding the orange battery ribbon in place. You only need to lift the locking bar up about 2 mm to free the cable.

Place the rear panel next to the iPod, being careful not to strain the orange headphone jack cable. Lift the hard drive up with one hand so you can access the headphone jack ribbon beneath. Use a spudger to flip up the plastic tab holding the headphone jack ribbon in place. The tab will rotate up 90 degrees, releasing the ribbon cable. Now to repair the damage caused by liberating the internal parts of the iPod Classic!

Opening these devices is not for the faint of heart. Getting inside one of these things requires some unusual tools. There are tack-welded springs down the inner sides of the back cover. These either hold on tenaciously or break with a momentum-inducing SPANG, ripping out the delicate headphone-jack ribbon cables and flinging them to the far corner of your workroom. Using a screwdriver means that your back cover — which is of course already scratched and dented — bends out of shape wherever the screwdriver goes.

The best way to apply the required force is with a wide, flat, thin, springy but strong object — a wallpaper scraper. Replacement battery: This is an optional item; I found that our original battery was in good shape, especially given the much lower current draw inherent to the SSD. On the other hand, while the back is not clipped on, this will probably be your only chance to put in a new battery. This is likely to be destructive, but only to the cover — even if you pull it off with some force, the ribbon connector that links it to the iPod motherboard will pull loose long before it causes any damage.

The technique required is to push a sharp blade between the side joint of the front and back covers: look carefully at our finished case to see how the metal casting of the front is shaped underneath the steel stamping of the back — this is the best place to push your blade. You are far too kind ; — stuffe. Go big or go home, I say. No, really far too kind — stuffe. Hippo Hippo 2, 4 4 gold badges 21 21 silver badges 31 31 bronze badges.

It uses an old hard drive with magnetic discs. Herr Herr 3 3 silver badges 19 19 bronze badges. The Overflow Blog. Does ES6 make JavaScript frameworks obsolete? Podcast Do polyglots have an edge when it comes to mastering programming Featured on Meta. Now live: A fully responsive profile. Related 1. Hot Network Questions. Question feed. Ask Different works best with JavaScript enabled.